A refractory wear model is only as good as the sensor data feeding it, and a thermocouple grid placed without regard for actual wear patterns, a thermal camera aimed at the wrong zone, or acoustic sensors positioned where they cannot pick up a meaningful signal will all quietly undermine even the best prediction algorithm. Getting sensor design right, before the modeling starts, is what determines whether a wear prediction is trustworthy enough to actually change how a furnace is operated and relined, and our team can walk through sensor placement design against your own furnace geometry.
Steel furnace, refractory life prediction
Design Sensor Placement That Actually Anchors a Trustworthy Wear Model
iFactory AI designs thermocouple grid placement, thermal camera positioning and acoustic sensor deployment around your furnace's actual wear patterns, not a generic template.
Why generic placement fails
A Wear Model Is Only as Good as Where the Sensors Sit
Refractory wear is rarely uniform across a furnace, so a thermocouple grid designed for even spacing rather than actual wear zones will systematically miss the areas that matter most.
Uneven wear
Certain zones wear faster based on furnace geometry and operation
Even sensor spacing
A generic grid treats every zone as equally important
Hot zones under-sampled
The areas wearing fastest get the least sensor coverage
Model misses critical wear
The prediction looks confident but is blind to the real risk area
Three sensor types
What Each Sensor Type Contributes to the Model
Thermocouple grid
Embedded temperature points that reveal heat profile changes as refractory thins.
Thermal camera
Surface temperature imaging that reveals hot spots across a wider area than point sensors.
Acoustic sensors
Pick up structural changes and stress signals not visible in temperature alone.
Review Your Own Furnace Wear Pattern
Share your furnace geometry and known wear history and see what a tailored sensor layout would look like.
Placement table
Matching Sensor Type to Furnace Zone
| Zone | Typical wear risk | Recommended sensor |
| Slag line | High, chemical and thermal attack | Dense thermocouple grid |
| Tap hole area | High, mechanical and thermal stress | Thermocouple grid plus acoustic |
| Side walls | Moderate, variable by furnace design | Thermal camera coverage |
| Bottom and hearth | Low to moderate, slower wear | Sparse thermocouple points |
Design process
Four Steps From Furnace Geometry to Sensor Layout
1
Review wear history
Identify which zones have historically worn fastest on this furnace.
2
Map zone risk
Rank furnace zones by expected wear risk based on geometry and operation.
3
Design sensor density
Concentrate sensors in high-risk zones rather than spacing evenly.
4
Validate against inspection
Confirm sensor readings match physical wear found during a scheduled reline check.
Common pitfalls
Three Mistakes That Undermine Sensor Design
1
Even spacing instead of risk-based placement
High-wear zones end up with the same sensor density as low-risk areas.
2
Single sensor type for every zone
Some zones need acoustic or thermal imaging that a thermocouple alone cannot provide.
3
No validation against physical inspection
Sensor readings are trusted without ever confirming they match actual measured wear.
Expert review
The temptation in sensor design is to spread coverage evenly because it feels fair and simple. Refractory wear is not even, and a model built on even sensor coverage will always underperform one built on actual wear-risk mapping.
Watch for
A sensor layout proposal that was not built from your furnace's own wear history.
Do next
Validate sensor readings against your next scheduled reline inspection before trusting the wear model fully.
— iFactory steel specialists
Frequently asked questions
What Plants Ask About Refractory Sensor Design
Can we use our existing thermocouples?
Existing thermocouples can often be incorporated into the design, though a review usually identifies gaps in high-risk zones that need additional sensors to give the model reliable coverage.
Ask about your current sensors.
How do we know which zones actually wear fastest?
Past reline records and inspection reports are the best starting point for mapping wear risk by zone, since they reflect what has actually happened on your specific furnace rather than a generic assumption.
Discuss your wear history.
Do we need all three sensor types on every furnace?
Not necessarily, since the right mix depends on your furnace's specific wear patterns, and some zones may only need thermocouple coverage while others benefit from adding thermal or acoustic sensing.
Talk through your sensor mix.
How is the sensor layout validated before relying on it?
Comparing sensor-based wear estimates against actual measurements taken during a scheduled reline inspection is the clearest way to confirm the model is reading the furnace accurately.
Ask about validation timing.
Does sensor placement need to change after a reline?
A reline is a good opportunity to review whether the sensor layout still matches the current wear pattern, since refractory design or operating conditions may have shifted since the original placement.
Discuss post-reline review.
From generic grid to wear-mapped design
Build a Sensor Layout That Actually Supports a Trustworthy Wear Model
Book a session with iFactory AI to review your furnace geometry and design a sensor layout around your real wear pattern.